Message |
---|
| Member | grafic Krasnoyarsk 11:58 13/09/2014 Posts 216 |
|
|
| Party | unnit Moscow 14:59 13/09/2014 1259 posts |
|
| Message Edit 15:06 - 13/09/2014 user unnit
Welcome, but nothing at all complicated ... this plate is inserted into the long end of the cover, keep the cover in front of him, put a plate on the left, then the wheel - teeth to the plate. Associate a thread that would not fall out, then cover assembly inserted into the cigarette lighter. The patent has but it is not very well see everything, if you need to lay it. |
|
| Party | unnit Moscow 15:21 13/09/2014 1259 posts |
|
| Here's a photo, so be clearer: |
|
| Member | grafic Krasnoyarsk 3:34 09/14/2014 Posts 216 |
|
|
| Party | unnit Moscow 15:45 09/15/2014 1259 posts |
|
| grafic writes: Thank you.
Well, it turned out to collect lighter? |
|
| Member | grafic Krasnoyarsk 7:15 09/16/2014 Posts 216 |
|
| Well in general yes, but will have to do a new rivet. Home too shortened when drilled. |
|
| Member | grafic Krasnoyarsk 16:53 09/11/2014 Posts 216 |
|
| Message Edit 17:14 - 11/09/2014 user grafic
Well, the final stage of repair IMCO-SOLO (with a jammed button and lid) Rivet of two elements 1 main shaft of the tube (new) 1a remnants of native dowel inserted in 1 (hat with remnants of the shaft) inserted in 1. You're cut off the shaft (taken from the reserve side for convenience) and riveted. The assembly process was pretty gemorno procedure was taken 3 times, and cast ptotom prepared snap. Most worryingly, the elements 2 (bracket) and 3,3a (spring loaded flint tube with the upper ears to insert rivets) during assembly, the motion of the lid is constantly shifting, causing the rivet enters with one hand and then rested against the fasteners on the other (natural spring, flints, and so mutually shifted) and everything had to be repeated over again. Apply the following: pursed silicic tube into position derefyannym sticks, with the help of instant glue has set a spring in the lid and stuck round gasket to kresalu. Result (intermediate) rivet vsavil. But as a result backlash COVER AND BUTTON STILL periodically wedge. PLEASE HELP! WHAT ELSE CAN I DO (where lock, preload, etc.) until completely riveted. |
|
| Party | unnit Moscow 20:39 11/10/2014 1259 posts |
|
| But as a result backlash COVER AND BUTTON STILL periodically wedge. PLEASE HELP! WHAT ELSE CAN I DO (where lock, preload, etc.) until completely riveted.
See more comb, usually from repeated use cloves and a little erased begin a snack. |
|
| Member | grafic Krasnoyarsk 3:44 11/11/2014 Posts 216 |
|
| Comb, of course, "zayuzanaya" I straightened up, brushed, but I think the reason is lyuchte entire spring-loaded system. By the way as flint tube attached I did not dopёr. Can not be removed completely, but up and down etc.-lion. walks about 2-3 mm. Completely disassemble (with drilling out rivets 2nd) do not want to, and completely ruin bayus (metal is old). |
|
| Party | unnit Moscow 13:15 11/11/2014 1259 posts |
|
| grafic writes:
Comb, of course, "zayuzanaya" I straightened up, brushed, but I think the reason is lyuchte entire spring-loaded system. By the way as flint tube attached I did not dopёr. Can not be removed completely, but up and down etc.-lion. walks about 2-3 mm. Completely disassemble (with drilling out rivets 2nd) do not want to, and completely ruin bayus (metal is old).
Her drill riveting do not just have to do a similar problematic. A flint tube rests only on on the top and bottom of the riveting part of the opening of the lower lid, and all looked at, too little backlash. |
|
| Member | grafic Krasnoyarsk 16:09 11/11/2014 Posts 216 |
|
| Message Edit 16:12 - 11/11/2014 user grafic
Well, I drilled the top, the tube can not be removed something from above holds (in my spring button syazany with a pipe). Maybe scheme / patent anyone there exists, and that in 0 disassemble well, not hunting. And since 2 months with one klёpkoy and assembly for ... .sya. Kraynyak gather a couple of times KC and the repository. I such on the pocket is not a burden, for that Chinese "Russian style" and have gas. |
|
| Party | unnit Moscow 16:18 11/11/2014 1259 posts |
|
| grafic writes: I-drilled top rail, tube is pulled out something from above holds (in my spring button syazany with a pipe). Maybe scheme / patent anyone there exists, and that in 0 disassemble well, not hunting. And since 2 months with one klёpkoy and assembly for ... .sya. Kraynyak gather a couple of times KC and the repository. I such on the pocket is not a burden, for that Chinese "Russian style" and have gas.
Patent evening look, I think for Solo was. |
|
| Member | grafic Krasnoyarsk 18:59 11/11/2014 Posts 216 |
|
| Ok! I want to have to finish the topic. And began to make a box for solo :) |
|
| Party | unnit Moscow 21:02 11/11/2014 1259 posts |
|
| grafic wrote: Ok! I want to have to finish the topic. And began to make a box for solo :)
Patent found, but it to PDF, I can throw in the mail. |
|
| Member | grafic Krasnoyarsk 00:39 12/11/2014 Posts 216 |
|
| Here's another thing annoying: the teeth of the lid (1) corresponds to the gear clutch with a button (2) -sleva but the right response clutch (2a) no. Maybe on my broken so skewed and jamming? PATENT skinte look |
|
| Party | unnit Moscow 13:14 12/11/2014 1259 posts |
|
| grafic writes: Here's another thing annoying: the teeth of the lid (1) corresponds to the gear clutch with a button (2) -sleva but the right response clutch (2a) no. Maybe on my broken so skewed and jamming? PATENT skinte look
Here is the answer ... comb should be on both sides, so skewed and shimming. In a personal address sbrost electric. Mail throw off patent. |
|
| Member | grafic Krasnoyarsk 17:58 12/11/2014 Posts 216 |
|
|
| Party | kirasa Moscow 18:35 12/11/2014 1732 posts |
|
| The impression is that mis-2a |
|
| Member | grafic Krasnoyarsk 20:23 12/11/2014 Posts 216 |
|
| Message Edit 20:27 - 12/11/2014 user grafic
I did not complete disassembly (lower klёpku not cleaned). 2a - a point on the diagram, where to my mind, DB mating gears. / 2a / in my opinion - is made in one piece with all vnutryankoy. As it can be put properly separately from the rest? I'm trying to decide what to do next: 1) try to make the item / 2 /, / 2a / (well in general all vnutryanku - difficult and not authentic), 2) to collect as is (simple but defective) - for the entourage, 3)? ?? HZ Although estesstvenno for daily use and will not apply. 4) What if someone realties completely "dead" is, but with entoy living part. ????? In any case, for a good scheme, mud photos, I will be very grateful. |
|
| Party | unnit Moscow 21:13 12/11/2014 1259 posts |
|
| grafic writes: I did not complete disassembly (lower klёpku not cleaned). 2a - a point on the diagram, where to my mind, DB mating gears. / 2a / in my opinion - is made in one piece with all vnutryankoy. As it can be put properly separately from the rest? I'm trying to decide what to do next: 1) try to make the item / 2 /, / 2a / (well in general all vnutryanku - difficult and not authentic), 2) to collect as is (simple but defective) - for the entourage, 3)? ?? HZ Although estesstvenno for daily use and will not apply. 4) What if someone realties completely "dead" is, but with entoy living part. ????? In any case, for a good scheme, mud photos, I will be very grateful.
Send a patent. |
|